A Study on Manufacturing of Flange Joint Used in Transportation Vehicle
Keywords:
Companion Flange, Drive shaft, Lath machine, Universal drive shaft, Industrial ManufacturingAbstract
Flange and flange connecting it to a commercial vehicle are processed in this investigation. Assemblies of Companion Flanges and Universal Drive shafts are also available. When the flange was brought in use in the commercial vehicles, it was seen that because if heavy friction, the part is deteriorating. To prevent this issue, a design was made which was further manufactured for accomplishing the goals of this study. When the product was ready, it was tested on CMM machine to find any type of error between the designed and manufactured product. The outcome obtained from the CMM machine showed a very small percentage of error. The new manufactured product had comparatively less amount of friction loss.
References
[1] C. Karaoǧlu and N. Sefa Kuralay, "Stress analysis of a truck chassis with riveted joints," Finite Elem. Anal. Des., vol. 38, no. 12, pp. 1115-1130, 2002, https://doi.org/10.1016/S0168-874X(02)00054-9
[2] F. Kirkemo, "Design of compact flange joints," Am. Soc. Mech. Eng. Press. Vessel. Pip. Div. PVP, vol. 433, no. January 2002, pp. 91-104, 2002, https://doi.org/10.1115/PVP2002-1087
[3] C. Sivakandhan and P. S. Prabhu, "Optimum Design and Analysis of the Drive Shaft in Composite Material," Mater. Sci. Res. India, vol. 8, no. 1, pp. 125-130, 2011, https://doi.org/10.13005/msri/080118
[4] A. Abel, T. Blochwitz, A. Eichberger, P. Hamann, and U. Rein, "Functional Mock-up Interface in Mechatronic Gearshift Simulation for Commercial Vehicles," Proc. 9th Int. Model. Conf. Sept. 3-5, 2012, Munich, Ger., vol. 76, pp. 775-780, 2012, https://doi.org/10.3384/ecp12076775
[5] M. Zulfadhli Bin and M. D. Zaki, "DESIGN AND ANALYSIS OF A COMPOSITE DRIVE SHAFT FOR AN AUTOMOBILE," Int. Rev. Appl. Eng. Res., vol. 4, no. 1, pp. 21-28, 2012.
[6] N. D. K. Sagar R Dharmadhikari, Sachin G Mahakalkar, Jayant P Giri, "'Design and Analysis of Composite Drive Shaft using ANSYS and Genetic Algorithm' A Critical Review," Ijmer, vol. 3, no. 1, pp. 490-496, 2013.
[7] M. kishore, J. Keerthi, and V. kumar, "Design and Analysis of Drive Shaft of an Automobile," Int. J. Eng. Trends Technol., vol. 38, no. 6, pp. 291-296, 2016, https://doi.org/10.14445/22315381/IJETT-V38P253
[8] P. Karthikeyan, R. Gobinath, L. Ajith Kumar, and D. Xavier Jenish, "Design and Analysis of Drive Shaft using Kevlar/Epoxy and Glass/Epoxy as a Composite Material," IOP Conf. Ser. Mater. Sci. Eng., vol. 197, no. 1, 2017, https://doi.org/10.1088/1757-899X/197/1/012048
[9] P. Seyfried, E. J. M. Taiss, A. C. Calijorne, F. P. Li, and Q. F. Song, "Light weighting opportunities and material choice for commercial vehicle frame structures from a design point of view," Adv. Manuf., vol. 3, no. 1, pp. 19-26, 2015, https://doi.org/10.1007/s40436-015-0103-8
[10] H. Mohrbacher, M. Spöttl, and J. Paegle, "Innovative manufacturing technology enabling light weighting with steel in commercial vehicles," Adv. Manuf., vol. 3, no. 1, pp. 3-18, 2015, https://doi.org/10.1007/s40436-015-0101-x
[11] P. N. Amrish, "Computer Aided Design and Analysis of Disc Brake Rotors," Adv. Automob. Eng., vol. 05, no. 02, 2016, https://doi.org/10.4172/2167-7670.1000144
