A Review on Design Analysis and Optimization of Front Axle For Commercial Vehicle
Keywords:
Front Axle Beam, Cross pin, Lean manufacturing, Design for manufacturingAbstract
To remain competitive in today's market, it is critical for manufacturers to provide new products to consumers at a lower cost and quicker than their competitors. The Front axle beam accounts for up to 40% of the vehicle's load-carrying capability. The existing measuring system shows quite a poor acceptability for the proposed design of the cross pin, except for the micrometer. A review is presented here on design analysis and optimization of cross pin. Literature is also studied of researchers and presented here on the same topic.
References
[1] J. Kral, M. Palko, M. Palko, and L. Pavlikova, "Design and development of ultra-light front and rear axle of experimental vehicle," Open Eng., vol. 10, no. 1, pp. 232-237, 2020, https://doi.org/10.1515/eng-2020-0032
[2] L. Jin, D. Tian, Q. Zhang, and J. Wang, "Optimal torque distribution control of multi-axle electric vehicles with in-wheel motors based on DDPG algorithm," Energies, vol. 16, no. 3, 2020, https://doi.org/10.3390/en13061331
[3] V. Murali, A. M. Ramananda, H. Nitin, and S. Pandit, "Design and Development of Four-Wheel Steering for All Terrain Vehicle ( A . T . V )," Int. Res. J. Eng. Technol., pp. 1660-1668, 2020.
[4] M. Zhileykin and A. Eranosyan, "Method of torque distribution between the axles and the wheels of the rear axle to improve the manageability of two-axle all-wheel drive vehicles," IOP Conf. Ser.
[5] Mater. Sci. Eng., vol. 820, no. 1, 2020, https://doi.org/10.1088/1757-899X/820/1/012008
[6] W. Wang, J. Li, G. Liu, and Z. Zhang, "Simulation study on ride comfort of three-axle heavy vehicle spatial model based on rigid-elastic model and pseudo-excitation method," J. Adv. Mech. Des. Syst. Manuf., vol. 14, no. 1, pp. 1-16, 2020, https://doi.org/10.1299/jamdsm.2020jamdsm0016
[7] BIPINWANKHEDE, "Failure Analysis of Automotive Front Wheel Drive Shaft," J. INFORMATION, Knowl. Res. Mech. Eng., vol. 4, no. 1, pp. 707-713, 2016.
[8] S. Nilkanth, I. Poonawala, and M. Ramgir, "Design Optimisation of Four Wheel Drive Tractor Front Axle Housing," Int. J. Eng. Res., vol. V4, no. 08, 2015, https://doi.org/10.17577/IJERTV4IS080114
[9] V. Helminen, M. Tiitu, L. Kosonen, and M. Ristimäki, "Identifying the areas of walking, transit and automobile urban fabrics in Finnish intermediate cities," Transp. Res. Interdiscip. Perspect., vol. 8, no. January 2019, p. 100257, 2020, https://doi.org/10.1016/j.trip.2020.100257
[10] K. Ulrich, "The role of product architecture in the manufacturing firm," Res. Policy, vol. 24, no. 3, pp. 419-440, 1995, https://doi.org/10.1016/0048-7333(94)00775-3
[11] L. R. Buckendale, Detroit, and Mich., "VEHICLE DRIVE AXLE," 1997.
[12] C. Singh, L. Kumar, B. kumar Dewangan, Prakash kumar sen, and K. Shailendra Bohidar, "A Study on Vehicle Differential system," Int. J. Sci. Res. Manag., vol. 2, no. 11, pp. 1680-1683, 2014.
[13] T. Soyusinmez, O. Güzelipek, T. Palandüz, and O. Ertuğrul, "Fracture Analysis of a Case- Hardened Kingpin," vol. 5, pp. 92-98, 2021. https://doi.org/10.3917/lhc.092.0098
[14] S. H. Kim and M. C. Shin, "Steering pull model and its sensitivity analysis," Appl. Sci., vol. 10, https://doi.org/10.3390/app10228072
[14] J. B. Marcomini, C. A. R. P. Baptista, J. P. Pascon, R. L. Teixeira, and P. C. Medina, "Failure Analysis of a Hot Forged SAE 4140 Steel Kingpin," Int. J. Eng. Res. Sci., vol. 2, no. 6, pp. 102-109, 2016.
[15] B. Vargas-Arista, J. Teran-Guillen, J. Solis, G. Garcia-Cerecero, and M. Martinez-Madrid, "Normalizing effect on fatigue crack propagation at the heat-affected zone of AISI 4140 steel shielded metal arc weldings," Mater. Res., vol. 16, no. 4, pp. 772-778, 2013, doi: 10.1590/S1516-14392013005000047.
[16] G. K. Triantafyllidis, A. V. Kazantzis, E. K. Drambi, E. A. Sami, and A. I. Kalantzis, "Fracture characteristics of torsion-bending fatigue and impact fatigue failure of two steel pins in a crawler excavator," J. Fail. Anal. Prev., vol. 9, no. 1, pp. 23-27, 2009, https://doi.org/10.1007/s11668-008-9196-8
[17] D. H. Kim et al., "Evaluation and experimental validation of steering efforts considering tire static friction torque and suspension and steering systems characteristics," SAE Tech. Pap., no. 724, 2007, https://doi.org/10.4271/2007-01-3641
