Process The Optimizations by Taguchi Method in Drilling Machine
Keywords:
Drill, drilling machine, taguchi method, Metal matrix composites, RoughnessAbstract
Material removal and surface roughness response are the primary goals of this research, which investigates and evaluates the effects of various input process parameters (cutting diameter and cutting speed) on these outcomes. Various variables have been taken into account in each experiment. The L9 Orthogonal array was used to design experiments during the milling of aluminium plate (work material). “Cutting diameter (10mm), cutting speed (1000rpm), and feed rate (0.014mm/rev)” are the most important input parameters for material removal rate and surface roughness.
References
[1] B. R. N. Murthy, R. Rangappa, and M. O. Almouns, "Optimization of thrust force in drilling of carbon-basalt hybrid composites through Taguchi and RSM," Mater. Today Proc., no. xxxx,
2020, https://doi.org/10.1016/j.matpr.2020.05.043
[2] C. Manickam and N. Parthipan, "Optimization of drilling parameters in AISI SS317L stainless steel material using Taguchi methodology," Mater. Today Proc., vol. 21, no. xxxx, pp. 837-842, 2020, https://doi.org/10.1016/j.matpr.2019.07.589
[3] Z. Krivokapić, R. Vučurević, D. Kramar, and J. Š. Jovanović, "Modelling surface roughness in the function of torque when drilling," Metals (Basel)., vol. 10, no. 3, pp. 1-15, 2020, https://doi.org/10.3390/met10030337
[4] K. Siva Prasad and G. Chaitanya, "Optimization of process parameters on surface roughness during drilling of GFRP composites using taguchi technique," Mater. Today Proc., vol. 39, no. xxxx, pp. 1553-1558, 2020, https://doi.org/10.1016/j.matpr.2020.05.562
[5] S. Jebarose Juliyana and J. Udaya Prakash, "Drilling parameter optimization of metal matrix composites (LM5/ZrO2) using Taguchi Technique," Mater. Today Proc., vol. 33, no. xxxx, pp. 3046-3050, 2020, https://doi.org/10.1016/j.matpr.2020.03.211
[6] K. Shunmugesh and A. Pratheesh, "Taguchi Grey Relational Analysis based Optimization of Micro-Drilling Parameters on Carbon Fiber Reinforced Plastics," Mater. Today Proc., vol. 24, pp. 1994-2003, 2019, https://doi.org/10.1016/j.matpr.2020.03.628
[7] K. S. Prasad and G. Chaitanya, "Analysis of delamination in drilling of GFRP composites using Taguchi Technique," Mater. Today Proc., vol. 18, pp. 3252-3261, 2019, https://doi.org/10.1016/j.matpr.2019.07.201
[8] M. K. Bharti, P. Girwal, and P. Patidar, "Improving Productivity and Maintainace Efficiency of an Automobile Industry Through Lean - Production Cum Maintance System," Int. J. Eng. Res. Gen. Sci., vol. 6, no. 6, pp. 6-18, 2018.
[9] D. Geng, D. Zhang, Y. Teng, and X. Jiang, "An experimental investigation on hole exit geometric error in orbital drilling process," Procedia CIRP, vol. 71, pp. 128-133, 2018, https://doi.org/10.1016/j.procir.2018.05.084
[10] K. S. Prasad and G. Chaitanya, "Selection of optimal process parameters by Taguchi method for Drilling GFRP composites using Abrasive Water jet machining Technique," Mater. Today Proc., vol. 5, no. 9, pp. 19714-19722, 2018, https://doi.org/10.1016/j.matpr.2018.06.333
